Tunze Turbelle NanoStream 6055 (264 to 1,453 GPH) Tunze Turbelle NanoStream 6055 (264 to 1,453 GPH)
SKU: 6055
Tunze

Tunze Turbelle NanoStream 6055 (264 to 1,453 GPH)

$219.99

Turbelle® nanostream® electronic is a speed-controlled pump operating on safety extra-low voltage, to be employed ideally in every aquarium from 40 to > 1,000 litres (10.5 to > 264 USgal.) for simulation of lapping waves or tidal currents. It contains a new microprocessor-controlled motor and thus can be called an “intelligent pump”: The electronic motor adapts its speed automatically to the pump load and always seeks the best efficiency at the lowest possible consumption of energy. This energy consumption is about fifty per cent lower than in conventional pump motors. The pumps will be stopped immediately in case of blockage. After the blockage has been removed, the pumps will start up automatically after a delay of 20 seconds. The pump driver has been provided with a fish care function, which causes a revolution of the screw every twenty seconds when the pump is at a standstill. It can be controlled by Multicontroller 7095, 7096 as well as Wavecontroller 7091, 7092.


Features:
  • New Generation with Titanium Alloy Shaft
  • For aquariums from 40 to 500 litres (11 to 132 USgal.)
  • Flow rate: 1,000 to 5,500 l/h (264 to 1,453 USgal./h)
  • Energy consumption: 4 - 18 W
  • Voltage / frequency: 115V/60Hz USA Plug
  • Cable length: 5 m (196.8 in.)
  • Dimensions: diam. 70 mm (2.7 in.), output: diam. 40/15 mm (1.5 / .59 in.)
  • Magnet Holder with Silence clamp up to a glass thickness of 15 mm (.59 in.).
  • Compatible with 7091, 7092, 7095, 7096 controllers

Initial operation for 6055 only


Plug the connector (1) of the power supply unit (2) into the corresponding socket (3) of the pump and subsequently connect the power supply unit to the mains (4). The power of the pump can be set directly on the power supply unit using the sliding switch to set between 12 V and 24 V (5). Singlecontroller (6) or Multicontroller (7) can be connected up to the connection of the Turbelle® nanostream 6055 as requested. For more precise information on the connection of Singlecontroller or Multicontroller, please refer to the corresponding instructions for use. Automatic shut-down The pump will be stopped immediately in case of blockage. After the blockage has been removed, the pump will start up automatically after a delay of 20 seconds. The pump control is thermally protected. The power supply unit is protected against shortcircuit and thermal overload.

Full Description
Qty
  • Description

    Turbelle® nanostream® electronic is a speed-controlled pump operating on safety extra-low voltage, to be employed ideally in every aquarium from 40 to > 1,000 litres (10.5 to > 264 USgal.) for simulation of lapping waves or tidal currents. It contains a new microprocessor-controlled motor and thus can be called an “intelligent pump”: The electronic motor adapts its speed automatically to the pump load and always seeks the best efficiency at the lowest possible consumption of energy. This energy consumption is about fifty per cent lower than in conventional pump motors. The pumps will be stopped immediately in case of blockage. After the blockage has been removed, the pumps will start up automatically after a delay of 20 seconds. The pump driver has been provided with a fish care function, which causes a revolution of the screw every twenty seconds when the pump is at a standstill. It can be controlled by Multicontroller 7095, 7096 as well as Wavecontroller 7091, 7092.


    Features:
    • New Generation with Titanium Alloy Shaft
    • For aquariums from 40 to 500 litres (11 to 132 USgal.)
    • Flow rate: 1,000 to 5,500 l/h (264 to 1,453 USgal./h)
    • Energy consumption: 4 - 18 W
    • Voltage / frequency: 115V/60Hz USA Plug
    • Cable length: 5 m (196.8 in.)
    • Dimensions: diam. 70 mm (2.7 in.), output: diam. 40/15 mm (1.5 / .59 in.)
    • Magnet Holder with Silence clamp up to a glass thickness of 15 mm (.59 in.).
    • Compatible with 7091, 7092, 7095, 7096 controllers

    Initial operation for 6055 only


    Plug the connector (1) of the power supply unit (2) into the corresponding socket (3) of the pump and subsequently connect the power supply unit to the mains (4). The power of the pump can be set directly on the power supply unit using the sliding switch to set between 12 V and 24 V (5). Singlecontroller (6) or Multicontroller (7) can be connected up to the connection of the Turbelle® nanostream 6055 as requested. For more precise information on the connection of Singlecontroller or Multicontroller, please refer to the corresponding instructions for use. Automatic shut-down The pump will be stopped immediately in case of blockage. After the blockage has been removed, the pump will start up automatically after a delay of 20 seconds. The pump control is thermally protected. The power supply unit is protected against shortcircuit and thermal overload.

  • Reviews

    Reviews

    Be the first to

  • Details

    Details

    Current Stock:
    SKU: 6055
    UPC: 4025167605505
    Manufacturer Part Number 6055
    Condition: New
    Weight: 2.90 LBS
    Width: 6.00 (in)
    Height: 4.00 (in)
    Depth: 7.00 (in)
  • Warranty

    Warranty

    2 YEAR MANUFACTURE LIMITED